Vega TH LINK Version 1.1 Installation Guide Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires de communication Vega TH LINK Version 1.1 Installation Guide. VEGA TH LINK Version 1.1 Installation Guide User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer

Résumé du contenu

Page 1 - Installation Guide

Doc. Version 1.1EnglishTH LINKInstallation Guide

Page 2 - Dear Customer

Design of the TH LINKTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK10Design of the TH LINK(see figure 1)1 Ethernet interface2LE

Page 3

Design of the TH LINKTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG11Fig. 1: TH LINK (front and side view)TH LINKTrebing &

Page 4 - About this Installation Guide

Design of the TH LINKTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK12Connections and indicating elements[1] Ethernet interface:

Page 5 - For your safety

Start-up guidelineTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG13Start-up guidelineThe following steps are required for start-

Page 6

Installing the TH LINKTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK14Installing the TH LINKInstalling the TH LINKFig. 2: Insta

Page 7

Connecting to EthernetTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG15Uninstalling the TH LINK1. Remove the connected supply an

Page 8 - Performance and functioning

Connecting the power supplyTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK16Connecting the power supplyDanger! Electrical voltag

Page 9 - Ethernet network presettings

Connecting the power supplyTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG17Fig. 3: Terminal strip for power supply on the TH LI

Page 10 - Design of the TH LINK

Configuring the TH LINK in the Ethernet networkTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK18Configuring the TH LINK in the E

Page 11

Configuring the TH LINK in the Ethernet networkTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG19SettingsClick on settings and th

Page 12 - Mounting

Doc. Version 1.1 | May 2012Dear Customer,This installation Guide will help you to install the hardware. If you have any further questions, please co

Page 13 - Start-up guideline

Configuring the TH LINK in the Ethernet networkTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK20User administrationHere you can

Page 14 - Installing the TH LINK

Configuring the TH LINK in the Ethernet networkTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG21Configuration method (DHCP/Manua

Page 15 - Connecting to Ethernet

Configuring the TH LINK in the Ethernet networkTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK22Connection in a network with man

Page 16 - Connecting the power supply

Configuring the TH LINK in the Ethernet networkTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG23Setting new IP and network addre

Page 17 - Earth conductor

Configuring the TH LINK in the Ethernet networkTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK244. If you want to use a DNS serv

Page 18

TH SCOPE settingsTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG25TH SCOPE settingsClick on settings > TH SCOPE.Here you can

Page 19 - Settings

TH SCOPE settingsTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK26MeasurementThe measurement settings include among other settin

Page 20 - Operation mode

TH SCOPE settingsTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG27Apply parametersBy default all TH LINK are set as parameter re

Page 21

Connecting the PROFIBUSTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK28Connecting the PROFIBUSThe 9-pin D-Sub socket is used fo

Page 22 - Default gateway 0.0.0.0

Connecting the PROFIBUSTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG29Fig. 7: Interface connection possibilities in the PROFIB

Page 23

ContentAbout this Installation Guide ...4Intended use ...

Page 24

Connecting the PROFIBUSTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK30Bus terminating resistorsTerminations of a PROFIBUS segm

Page 25 - TH SCOPE settings

Firmware updateTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG31Firmware updateFirmware updates for the TH LINK are available fr

Page 26 - Set parameter provider

TroubleshootingTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK32Troubleshooting– Check the power supply (LED RUN must light gree

Page 27 - Parameters

TroubleshootingTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG33– Internal error or defect: Please contact the Technical Support

Page 28 - Connecting the PROFIBUS

Technical dataTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK34Technical dataElectrical dataNominal supply voltage (limit value

Page 29

General conditionsTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG35General conditionsRight to make additions or alterationsTrebi

Page 30 - Setting PROFIBUS parameters

Doc.Nr. 10003010 © Trebing & Himstedt Prozeßautomation GmbH & Co. KG

Page 31 - Firmware update

About this Installation GuideTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK4About this Installation GuidePlease read this insta

Page 32 - Troubleshooting

For your safetyTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG5Menu and keyboard commandsThe following conventions apply to menu

Page 33

For your safetyTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK6– Carefully plan the integration of the TH LINK into an existing

Page 34 - Technical data

For your safetyTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG7– High temperature differences between the storage site and insta

Page 35 - General conditions

Performance and functioningTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK8Performance and functioningThe TH LINK provides acces

Page 36

Performance and functioningTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG9Configuration requirements(not included in the scope

Commentaires sur ces manuels

Pas de commentaire